スキルを探す

Firmware development for the 38-pin ESP32-WROOM-32 development board — Espressif ESP32-DevKitC V4, Ai-Thinker NodeMCU-32S, DOIT ESP32 DevKit V1 38-pin and their CH340/CP2102 clones, 19 pins per side, with GPIO0 and the six in-package flash pins (GPIO6-11, labelled D0 D1 D2 D3 CMD CLK or SD0-SD3) broken out. Use when working on a 38-pin ESP32 devkit (ESP32-D0WDQ6 / ESP32-D0WD-V3, ESP-WROOM-32 or ESP32-WROVER module): project setup, platformio.ini and sdkconfig for ESP-IDF or Arduino, pin mapping and which GPIOs are safe, the flash-pin and IO0 traps, WROVER GPIO16/17 PSRAM conflict, strapping pins, ADC1 vs ADC2 with Wi-Fi, SPI speed and IO_MUX pins, deep sleep and RTC wake pins, flashing, BOOT/EN recovery, brownouts, or debugging why something on the board does not work.

日本語の概要は準備中です。原文の説明を表示しています。

Firmware development for the ESP32-C3 0.42" OLED board (ESP32-C3FH4, QFN32) — the ABRobot / 01Space "ESP32-C3-0.42LCD" mini board and its clones, sold as "ESP32-C3 SuperMini with OLED" and "ESP32 C3 OLED development board". Covers its 72x40 SSD1306 OLED on I2C, the single I2C bus, blue LED on GPIO8, BOOT button on GPIO9, USB Serial/JTAG console, ADC1, Wi-Fi/BLE, and the ESP-IDF + PlatformIO setup around them. Use when working on this board or a bare ESP32-C3: project setup, platformio.ini and sdkconfig, pin mapping and strapping pins, getting the 0.42-inch display to show something other than snow, U8g2 offsets, adding a second I2C device, flashing over USB-C, or debugging why something on the board does not work.

日本語の概要は準備中です。原文の説明を表示しています。

Firmware development for the Waveshare ESP32-C6-LCD-1.47 board (ESP32-C6FH4, QFN32) — its 1.47" 172x320 ST7789 LCD, WS2812 RGB LED, microSD/TF slot, USB-Serial-JTAG console, Wi-Fi 6/BLE/802.15.4 radio, and the ESP-IDF + PlatformIO setup around them. Use when working on this board or the ESP32-C6-LCD-1.47-M variant (SKU 28563 / 30381, WS-28563): project setup, platformio.ini and sdkconfig, pin mapping and strapping pins, LCD or SD bring-up on the shared SPI bus, backlight brightness, display frame rate, flashing over Type-C, or debugging why something on the board does not work.

日本語の概要は準備中です。原文の説明を表示しています。

Firmware development for the Waveshare ESP32-C6-Touch-LCD-1.47 board (ESP32-C6FH8, QFN32, 8 MB flash, SKU 31203 / 31201-M) — its 1.47" 172x320 JD9853 IPS panel, AXS5106L capacitive touch controller on I2C 0x63, QMI8658A IMU on I2C 0x6B, microSD/TF slot on the shared SPI2 bus, ETA6098 battery charger with VBAT sensing, USB-Serial-JTAG console, Wi-Fi 6/BLE/802.15.4 radio, and the ESP-IDF + PlatformIO setup around them. Use when working on this board: project setup, platformio.ini and sdkconfig, pin mapping and strapping pins, JD9853 bring-up, touch coordinates and calibration, LVGL memory budgeting, backlight PWM, TF card on the shared bus, battery voltage, flashing over Type-C, or debugging why something on the board does not work. This is NOT the non-touch ESP32-C6-LCD-1.47 (ST7789, 4 MB) — the two share a name and almost no pins.

日本語の概要は準備中です。原文の説明を表示しています。

Firmware development for the 40-pin ESP32-S3-WROOM-1 camera board — the Freenove ESP32-S3-WROOM (FNK0085) and the AliExpress "ESP32-S3 CAM" / "ESP32-S3-WROOM N16R8 CAM" clones that copy its header: 20 pins a side, a 24-pin DVP camera FPC connector for an OV2640/OV3660, an on-board microSD slot on the SDMMC bus, a WS2812, two USB-C sockets (CH343 bridge and native USB), ESP32-S3-WROOM-1-N8R8 or N16R8 with 8 MB octal PSRAM. Use when working on this board or any ESP32-S3 DVP camera board: project setup, platformio.ini, the qio_opi PSRAM memory type, camera and SD_MMC pin maps, esp_camera_init failures, PSRAM not found, frame buffer allocation, SD card mount failures, which GPIOs are left once the camera is wired, strapping pins, ADC1/ADC2, flashing over the two USB ports, BOOT/RESET recovery, brownouts, or debugging why the camera, the card or the board does not work.

日本語の概要は準備中です。原文の説明を表示しています。

Firmware development for the 30-pin NodeMCU ESP8266 devkit — NodeMCU DevKit V1.0 / Amica (CP2102) and LoLin NodeMCU V3 (CH340G), built on the Ai-Thinker ESP-12E or ESP-12F module (ESP8266EX, 4 MB flash), with PlatformIO and the Arduino ESP8266 core (`board = nodemcuv2`). Use when working on a NodeMCU, ESP-12E, ESP-12F or ESP8266 devkit: project setup, platformio.ini, the D0-D10 vs GPIO numbering, which pins are safe and which break the boot, GPIO15/GPIO0/GPIO2 strapping, the A0 divider and 1 V ADC, software I2C and software PWM, analogWrite range, LittleFS and flash layouts, OTA, deep sleep and the missing GPIO16-to-RST link, Wi-Fi, heap exhaustion, watchdog and Soft WDT resets, exception decoding, flashing over CP2102/CH340, or debugging why the board does not boot, prints garbage, or reboots by itself.

日本語の概要は準備中です。原文の説明を表示しています。

Firmware development for the ProMicro nRF52840 (V1940) — the nice!nano v2 compatible clone also sold as SuperMini nRF52840, nRF52840 Pro Micro or nRFMicro (nRF52840 QIAA, Cortex-M4F @ 64 MHz, 1 MB flash / 256 KB RAM, BLE 5 + 802.15.4, native USB, Adafruit UF2 bootloader with SoftDevice S140). Covers the PlatformIO + Adafruit nRF52 Arduino setup for a board that ships in neither, the vendored board definition and Pro Micro pin map, USB CDC via TinyUSB, Bluefruit BLE, the 32.768 kHz crystal that clones omit, SAADC pins, NFC pins as GPIO, and Zephyr's promicro_nrf52840 board target. Use when working on this board or any nice!nano v2 / ZMK keyboard controller: project setup, platformio.ini, pin mapping, LED not blinking, double-tap RESET and UF2/DFU flashing, SoftDevice version mismatches, a board that enumerates but never runs, or debugging why something on the board does not work.

日本語の概要は準備中です。原文の説明を表示しています。

Firmware development for the Raspberry Pi Pico (original, RP2040 — dual Cortex-M0+ @ 133 MHz, 264 KB SRAM, 2 MB QSPI flash) — its 26 exposed GPIO, 4-channel 12-bit ADC, 16-channel PWM, 2× UART/I2C/SPI, PIO state machines, USB 1.1 CDC, VSYS/VBUS/SMPS power wiring, and the PlatformIO + arduino-pico (earlephilhower) setup around them. Use when working on this board, any Pico H or Pico clone, or a bare RP2040: project setup, platformio.ini, the earlephilhower-vs-Mbed core choice, pin mapping, USB CDC serial, analogRead/analogWrite behaviour, Wire/SPI defaults, battery power, EEPROM emulation, BOOTSEL/UF2 flashing, or debugging why something on the board does not work.

日本語の概要は準備中です。原文の説明を表示しています。

Firmware development for the WeAct Studio RP2350A Core Board (RP2350A — dual Cortex-M33 @ 150 MHz, 520 KB SRAM, 4 MB or 16 MB QSPI flash) in both of its revisions, RP2350A_V10 and RP2350A_V20 — the 40-pin Pico-2-shaped header, 3-or-4-channel 12-bit ADC, PWM, PIO, USB-C CDC, the V1.0 LDO vs V2.0 buck-boost power wiring, and the PlatformIO + arduino-pico (earlephilhower) setup around them. Use when working on this board, a WeAct RP2350 core board of unknown revision, or any Raspberry Pi Pico 2 / RP2350A clone: project setup, platformio.ini, board = rpipico2 vs weact_rp2350b, telling V1.0 and V2.0 apart, pin mapping, LED and KEY pins, powering it from a battery, 4 MB vs 16 MB flash, erratum RP2350-E9 pull-down trouble, BOOT/RESET UF2 flashing, or debugging why something on the board does not work.

日本語の概要は準備中です。原文の説明を表示しています。

Firmware development for the WeAct Studio "Black Pill" (STM32F411CEU6) and its clones such as the DFRobot DFR0864 — the 25 MHz HSE and 32.768 kHz LSE crystals, PC13 LED, K1 button, USB-C wired straight to USB_OTG_FS, ROM DFU flashing, the SPI-flash footprint, and the STM32Cube HAL + PlatformIO setup around them. Use when working on this board or any STM32F411CE/F401CC Black Pill: project setup, platformio.ini, clock and PLL configuration for 96 MHz plus 48 MHz USB, pin mapping on the 48-pin package, USB CDC console, RTC on the LSE crystal, the internal temperature sensor, ADC accuracy, DFU flashing and recovery, or debugging why something on the board does not work.

日本語の概要は準備中です。原文の説明を表示しています。

Firmware development for the WeAct Studio MiniSTM32H7xx core board (STM32H750VBT6) — its 0.96" ST7735 TFT, DVP camera, QSPI/SPI flash, MicroSD, USB, and the STM32Cube HAL + PlatformIO setup around them. Use when working on this board or any STM32H750/H743 WeAct core board: project setup, platformio.ini, clock/PLL configuration, pin mapping, peripheral bring-up, LCD performance, D-cache/DMA problems, DFU flashing, or debugging why something on the board does not work.

日本語の概要は準備中です。原文の説明を表示しています。

Firmware development for the <VENDOR> <BOARD NAME> (<MCU PART NUMBER>) — its <peripheral>, <peripheral>, <peripheral>, and the <SDK/HAL> + <build system> setup around them. Use when working on this board or any <compatible siblings>: project setup, <config file>, clock configuration, pin mapping, peripheral bring-up, <the board's headline concern>, flashing, or debugging why something on the board does not work.

日本語の概要は準備中です。原文の説明を表示しています。

Firmware development for the Arduino Nano (A000005, ATmega328P @ 16 MHz, 5 V) — its 30 KB usable flash, 2 KB SRAM, 1 KB EEPROM, 8-channel 10-bit ADC, six 8-bit PWM pins across three timers, UART shared with the USB-serial chip, I2C on A4/A5, SPI on D10–D13, sleep modes, and the Arduino AVR core + PlatformIO setup around them. Use when working on this board or any ATmega328P Nano clone (FTDI or CH340 USB): project setup, platformio.ini, old-vs-new bootloader uploads, pin mapping, A6/A7 restrictions, timer/Servo/tone conflicts, the 2 KB SRAM budget, analog references, powering from VIN, ICSP recovery, or debugging why something on the board does not work.

日本語の概要は準備中です。原文の説明を表示しています。

Observes runtime behavior of binaries via QEMU emulation, GDB debugging, and Frida hooking — syscall tracing, breakpoints, memory inspection, and function interception. Use when running, tracing, or debugging a binary, verifying hypotheses from static analysis, or watching actual syscalls, network calls, or file access; requires human approval before any execution.

日本語の概要は準備中です。原文の説明を表示しています。

Expert code reviewer focusing on quality, maintainability, performance, and best practices

日本語の概要は準備中です。原文の説明を表示しています。

Comprehensive MCP server development guide covering FastMCP 2.14.3 features, Anthropic standards, ecosystem integration, and production deployment across all agentic IDEs

日本語の概要は準備中です。原文の説明を表示しています。

Master debugger for Python code with expertise in common errors, performance issues, and debugging tools

日本語の概要は準備中です。原文の説明を表示しています。

Database expert for query optimization, indexing, schema design, and performance tuning

日本語の概要は準備中です。原文の説明を表示しています。

Code refactoring expert for improving code quality, reducing technical debt, and safe transformations

日本語の概要は準備中です。原文の説明を表示しています。

Expert in optimization methods covering linear programming, convex optimization, gradient methods, and constrained optimization

日本語の概要は準備中です。原文の説明を表示しています。

Use when planning, scaffolding, validating, or packaging Claude skills inside Advanced Memory MCP.

日本語の概要は準備中です。原文の説明を表示しています。

Publishes structured, actionable artifacts from Claude Code sessions — PR walkthroughs, incident timelines, system explainers, release checklists, and security audits.

日本語の概要は準備中です。原文の説明を表示しています。

Generates structured engineering specs (backend or frontend) from feature descriptions, designs, or ticket references. Triggers on "spec", "story", "ticket", "engineering spec", "write a story for", "write a spec for", "create a ticket for".

日本語の概要は準備中です。原文の説明を表示しています。

Generate OpenAPI 3.1 documentation from your API codebase. Auto-detects Express, Fastify, NestJS, Django, FastAPI, Flask, Rails, Spring, Go, and more. Triggers: you need API documentation, OpenAPI spec, Swagger docs, endpoint reference, or REST API docs.

日本語の概要は準備中です。原文の説明を表示しています。